Telescopic Conveyors

LB-33T4

LB-40T5

Tower Mount

Equipment Highlights


Telescopic Conveyor

Outriggers and telescopic conveyor, Glenn Ellyn All tubular steel welded construction. Each section is a welded box lattice frame designed and proportioned to carry the loads applied to it. This results in a lighter structure with a high strength to weight ratio and greater stiffness than aluminum structures. Our conveyor belt is supported by fully U-troughed rollers for increased capacity and cleanliness. Base section frame is designed with offset lower chord members to provide for clearance to conventional truck cab in the road transport position.

Transfer Turntable

Object is to provide a turntable to attach discharge end of feed conveyor and provide a dimensional change between road travel, lowered position and operational, raised position. This is necessary to provide a flow path for the concrete or aggregate materials to transfer from the feed conveyor to the telescopic conveyor. Transfer turntable is connected to the main turret with a plurality of transfer arms. These arms are pinned to the transfer turntable and to the main turret, which allows rotation from a lowered, road travel position to a raised, operational position. The raised position results in the transfer turntable being level and co-axial with the main turntable/turret. Pinned connections have replaceable bushings and are equipped with grease fittings to provide smooth, reliable operation.

Traction Drive

Traction drive frame structure is built into the base section for increased strength and rigidity. The traction drive mechanical components are located outside the base section where they are easily removable for maintenance and service. The traction drive wire rope system is simplified with fewer sheaves and shorter wire rope length. Force for telescopic movement is applied only to the inner-mid section. The remaining sections are pulled in or out with equalizer cables of smaller proportions. Mono-block slide pads between the sections are easily removable for replacement and can be shimmed to compensate for wear and adjusted for proper clearance.

Feed Conveyor

Pin-on design to transfer turret allows for easy removal for maintenance and service. The upper conveyor section is fixed at a negative angle to provide a better belt transition and material flow into the transfer area. This allows much cleaner operation and controls spillage of material. Too sharp of an angle will launch material off the belt resulting in loss of material and dirty operation. The feed conveyor is equipped with a powered hinge and control arm. The object is to provide a hinge mechanism, which allows feed conveyor contact with the ground without adding extra stress on the structure. Free-floating hinge and control arm allow for full retraction of the hydraulic cylinders. Feed conveyor contact with the ground is under self-weight only. Hydraulic cylinder pressure is monitored and switched to allow full use of telescopic conveyor while feed conveyor is securely in contact with the ground. Minor variations in machine leveling, due to outrigger pad settlement, are automatically compensated for with control arm float position. By lowering the feed conveyor into contact with the ground, further retraction of the hydraulic cylinder will rotate the control arm away from the conveyor saddle area thereby allow the lower conveyor section to be free-floating. Full retraction of the hydraulic cylinders will build hydraulic fluid pressure to a higher level. This pressure activates a pressure switch, which sends a signal to enable the telescopic conveyor electrical controls.

> Return to Top



Equipment

New! Download the Brochure


LB-33T4-20

Conveyor Specifications
Conveyor Reach (Max 0-28°) 107'1" 33M
Discharge Height from Grade to 28° 61’7" 18.78M
Main and Feeder Rate Capacity at 0 8 cu-yd/min; 480 cu-yd/hour 6.4cu-m/min; 384 cu-m/hr
Belt Width Main and Feed 20” 508mm
Outrigger Spread 27’10” 8.47M
Component Specifics
Belting Continental Belting
Wireless Remote Scanreco
PTOs MUNCIE/MACK
Proportional Valve HAWE
Oil Cooler ASA
Filtration Hydac-Zinga
Water Pump Loop Belt Low Pressure
Truck MACK MRU
Travel Mode Axle Weights
Steering 19,373 lbs 8,787 Kg
Tandem 32,927 lbs 14,956 Kg
Pusher 16,860 lbs 7,648 Kg
Total 69,205 lbs 31,391 Kg
Loop Belt Industries is proud to announce the newest truck-mounted conveyor in it's product line-up.Loop Belt Industries is proud to announce the newest truck-mounted conveyor in it's product line-up.

With over 107' (33m) of reach and 20" wide belts, this conveyor can handle low to no-slump concrete and aggregates up to 6".

It's ideal for a wide range of projects from footings and foundations,to bridge decks, mat pours and wind energy tower foundations. The LB33 has numerous design enhancements and features focused on ease of operation and maintenance.

The LB33 is truly a low cost of operation machine that will provide many years of profitable service.
> Return to Top



LB-40T5-20

Download the Brochure
Conveyor Specifications
Conveyor Reach (Max 0-30°) 129’ 9” 39.56M
Discharge Height from Grade to 30° 72’ 5” 22.07M
Main and Feeder Rate Capacity at 0 8 cu-yd/min; 480 cu-yd/hour 6.4cu-m/min; 384 cu-m/hr
Belt Width Main and Feed 20” 508mm
Outrigger Spread 32’ 3” 9.83M
Component Specifics
Belting Continental Belting
Wireless Remote Scanreco
PTOs MUNCIE/MACK
Proportional Valve HAWE
Oil Cooler ASA
Filtration Hydac/Zinga
Water Pump Loop Belt Low Pressure
Truck Mack/MRU
Travel Mode Axle Weights
Steering 35,660 lbs 16,176 Kg
Tandem 45,080 lbs 20,448 Kg
Total 80,740 lbs 36,624 Kg
The LB40 provides the longest reach of any truck-mounted conveyor in the industry. Equipped with a 20" wide belt, its capacity and reach are unmatched.

> Return to Top



TTLB-40T5-20

Download the Brochure
Conveyor Specifications
Conveyor Reach (Max 0-30°) 129’ 9” 39.56M
Discharge Height from Grade to 30° 72’ 5” 22.07M
Main and Feeder Rate Capacity at 0 8 cu-yd/min; 480 cu-yd/hour 6.4cu-m/min; 384 cu-m/hr
Belt Width Main and Feed 20” 508mm
Outrigger Spread 32’ 3” 9.83M
Component Specifics
Belting Continental Belting
Wireless Remote Scanreco
PTOs Funk Gearbox
Engine JOHN DEERE 6068HF-285
Proportional Valve HAWE
Oil Cooler ASA
Filtration Hydac/Zinga
Water Pump Loop Belt Low Pressure
Truck N/A
Travel Mode Axle Weights
Three Trailer Axles 54,540 lbs 29,739 Kg
King Pin 21,900 lbs 9,934 Kg
Total 76,440 lbs 34,673 Kg
The LB40 provides the longest reach of any truck and Trailer mounted conveyor in the industry. Equipped with a 20" wide belt, its capacity and reach are unmatched.

> Return to Top



Tower Mount

Download the Brochure
Conveyor Specifications
Conveyor Reach (Max 0-28°) 129’ 9” 39.56M
Discharge Height from Grade to 28° with two tower segments 103' 2" 31.44M
Main and Feeder Rate Capacity at 0 8 cu-yd/min; 480 cu-yd/hour 6.4cu-m/min; 384 cu-m/hr
Belt Width Main and Feed 20” 508mm
Tower Segments 20' 0" 6.10M
Component Specifics
Belting Continental Belting
Wireless Remote Scanreco
PTOs N/A
Proportional Valve HAWE
Oil Cooler ASA
Filtration Donaldson
Water Pump Loop Belt Low Pressure
Tower mounted telescopic conveyors are perfect for dams and other large civil projects that require higher elevations. Tower mounted conveyors can be fixed or mobile; attached to a traveler base.

> Return to Top

Call 630-552-5303 or contact us online for telescopic conveyor services.

Telescopic Conveyors | Glen Ellyn, Illinois

Loop Belt Industries specializes in telescopic conveyors for placing concrete and a variety of materials including RCC. Loop Belt designs truck mounted and pedestal mounted conveyors as well as long line conveyors and a variety of hoppers. Loop Belt's sister company, Illinois Conveyor Enterprises, provides parts and services to recondition and repair Loop Belt™ conveyors, Super Swinger conveyors and conveyors and related machinery from other manufacturers.